Microsoft Word – ATLANTIC – EXTERIOR RENOVATION PERMIT
Asphalt shingles shall have the minimum number of fasteners required by the manufacturer 1504.1. Asphalt shingles shall be secured to the roof with not less than four fasteners …Read more

BYU CITY FIRE STATION ASPHALT SHINGLES 07311 – 1 SECTION …
Fasten asphalt shingles to roof sheathing with nails. B. Felt Underlayment: Apply 1 layer of 30 lb. felt underlayment horizontally over entire surface to. receive asphalt shingles, lapping succeeding courses a minimum of 2 inches Install asphalt shingles, beginning at roof’s lower edge, with a …Read more

The Durability and Longevity of Metal Roofs
typical roofing styles including cedar shake, slate, tile, shingle, and standing seam vertical panels the steel in a metal roof is about 56% from production to installation to reuse – far superior to asphalt. …Read more

CITY OF RIVERSIDE
2. New overlay roofing to be asphalt shingle (a.k.a. composition shingles) The existing roofing material was asphalt shingle with a maximum of one existing layer of asphalt. shingles for a combined total of two layers of roofing material (one existing and one new) …Read more

The Right Choice.
IKO is not liable for damage caused to products installed over a roof deck. that is not properly ventilated with IRON CLAD Shingle. Limited Warranty — from 5 to 10 years for IKO’s Asphalt. shingles to an …Read more

QUOTATION REQUEST #45-04
Quotations are invited for roof shingles replacement at the Carnegie Library – Core Building, 5017 Victoria Avenue, Only after the completion of the shingle underlay membrane, can the new asphalt shingle roof be applied. …Read more

Architectural Reference
Re-roof over asphalt shingles. Batten or Battenless Install. Re-roof over wood shake shingles. Panel Width. 15.58″ Panel Length. 43.84″ Pcs/Square. 24 Panels. Weight/ sq. ft. 1.2 lbs. Substrate. 26 Gauge. Zincalume® Installation. Solid Sheathing. Open Rafter. Minimum Roof Slope. 3:12. Maximum Roof Slope …Read more

Summary of Products FL # Model, Number or Name
Other: Asphalt shingles shall be used only on. roof slopes of 2:12 or greater. Not Other: Asphalt shingles shall be used only on. roof slopes of 2:12 or …Read more

Don’t Of Slate Roof Installation

Everyone talks about what to do in slate roof installation but here we will talk about don’ts of slate roof installation.

Do not do the following things while installing the slate roof

1. Never walk on the slate roof when you are installing it.
2. The length of the headlap should not be less than 3 inches
3. Never use electrogalvanized nails to install slate roof. Instead of this you can use copper or stainless steel nails for slate roof installation.
4. Aluminium drip edges are not recommended to make slate roofs. These are made for asphalt shingle roofs. For slate roof use copper or stainless steel aprons.
5. Never pick the slate on the basis of color and pattern. Always look for quality, thickness, weight and other properties.
6. Slate roof tiles of 3/16″ to 1/4″ should not have drilled holes. These should have punched holes in the slate tiles.
7. Never think that underlayment will work as water resistant. It works till the slate roof installation. To make slate roof a water proof you will have to install it properly.
8. Use of laminated wood roof decking is not recommended for slate roof. Instead of this use solid lumbar.
9. Never install the loosen fascia. All the ends must be completely nailed.
10. Never work on assumptions while installing slate roof. Always draw horizontal lines taking correct dimensions to install each row of slate tile.
11. Never use cement or caulk to fix the slate. This will make the repair job difficult if required in future. Copper or stainless steel nails will perfectly install the slate roof.
12. Never start installing slate roof without prior knowledge.
13. Do  not punch the holes in slate while installing. Make the holes before installation.
14. Put your starter slate with back side up
15. Neither use  too many or too less number of nails.
16. Do not use poor quality of flashing material. Either use copper flashing or stainless steel flashings.
17. While signing a contract with slate contractor or installer read the documents carefully and never leave anything on assumptions. Because you will get what is written.